Tel - 028.350.55209
Tinsley việt nam EN
Tinsley việt nam EN

Dual Channel Transformer Micro-Ohmmeter 5896C

Features
 
  • RX range 20 mW (10-60A) to 6kW (10mA)
  • Maximum resolution 0.01mW
  • Automatic range selection
  • Current setting from 0.01 to 60A
  • Fast core saturation with 60V
  • Test objects up to 150MVA with 5 to 10A, 500MVA with 20 to 60A
  • "Heat Run” measurement including algorithm
  • (resistance at t=0)
  • Measuring uncertainty ± 0.1% of reading
  • Temperature measurement and compensation to 20°C with T/C’s for both “Cu” and “Al”
  • RS232C port for full external control of the instrument
  • Centronics printer interface
 
For more information about this product contact Tinsley
 
 
Dual Channel Transformer Micro-Ohmmeter 5896C

General

THE ADVANTAGE OF THE 5896C IS ITS SIMPLICITY OF USE
 
The Tinsley 5896C is specifically designed to measure the resistance of highly inductive loads such as transformers, motors and generators. It has a measurement resolution of 0.01µW for the 20µW range and can measure resistances up to 6kW. Transformers up to 500 MVA and above can be measured. A specially designed current source is used to quickly saturate the device core and obtain a stable resistance reading in the shortest possible time.
 
So that the highest resolution of the reading is always displayed, range selection is performed automatically and therefore is not necessary to be set by the operator.
 
When required, a temperature compensation feature allows the reading to be corrected to the 20°C equivalent value by either entering the actual temperature of the unit under test or by using a PT100 temperature probe. A correction can be selected for either copper or aluminium windings.
 
When used for automatic “Heat Run” tests, measurements are made at preset time intervals and an internal algorithm is used to calculate the resistance at t=0. The transformer is made safe after testing by discharging stored energy into the 5896C attenuation resistor and varistors. Only a negligible residue will remain when the discharge warning light indicates that it is safe to remove the test leads.
 
The 5896C uses the four-wire measurement technique to eliminate the effect of the resistance of the test leads. By using the dual inputs of the 5896C it is possible to measure both a low voltage and the high voltage winding of a transformer at the same time. This can greatly reduce the time taken to produce cooling curves with an added advantage that the stability of the low voltage winding measurement can be improved when the high voltage winding is energised by the 5896C at the same time.
 
The 5896C can be used to control the transformer tap changer. Therefore automatic measurement is possible with no need to remove the current between each tap change. During switching the inputs of the instrument are protected to avoid damage that could occur should a tap changer prove to be faulty during testing.
 
Specifications

See the table below for a run-down of this product's specifications.

Resistance Range
20mW (10-60A) to 6kW (10mA)
Resolution
0.01mW e.g. 150.01mW (4-1/2 digit)
Accuracy
+/- 0.1% of reading
Max. Voltage
60V pure DC (Noise < 10mVpp)
Max. Current
60A pure DC
Selectable max. current
10mA to 60A, limited by total resistance (cable + object)
Measuring time
Short due to very fast charge with 60V available
Discharge time
Typically 1/10 of charging time
Measuring inputs
Measuring inputs 2 Current, 4 Potential (2 channels)
Temperature input
Connector for PT100 (correction for 20/23°C for Cu or Al)
Tap changer
Connector for automatic up/down control
Warning system
Connector for red/green warning lamps
External start
Connector for measurement start via external contact
External current supply
Connector for controlling currents up to 600 A, automatically
extends range down to 2mW (resolution 0.001mW = 1nW)
Mains
85 to 260 VAC, 6.5A, Auto ranging
Display
LCD 240 x 128 with back light
Interface
RS232C
Printer
Built-in thermal printer
Test storage
Up to 1000 results
Environment (operating)
-10°C to 50°C
Environment (storage)
-30°C to 60°C
Environment (humidity)
0 - 90% R/H max., non condensing
Size (without cables)
490 x 400 x 190 mm (WxDxH, mobile ABS rugged case)
Weight (without cables)
Approx. 15kg
Cables
Various options available
Safety and EMC
CE, IEC-1010-1, EN55022 B, EN61000-3-2.-3 , ENV50204